this post was submitted on 17 Sep 2024
1 points (100.0% liked)

PC Master Race

15061 readers
10 users here now

A community for PC Master Race.

Rules:

  1. No bigotry: Including racism, sexism, homophobia, transphobia, or xenophobia. Code of Conduct.
  2. Be respectful. Everyone should feel welcome here.
  3. No NSFW content.
  4. No Ads / Spamming.
  5. Be thoughtful and helpful: even with ‘stupid’ questions. The world won’t be made better or worse by snarky comments schooling naive newcomers on Lemmy.

Notes:

founded 2 years ago
MODERATORS
 
top 19 comments
sorted by: hot top controversial new old
[–] [email protected] 0 points 3 months ago (1 children)

If by FPS you mean Fahrenheit per second then yes. 👍

[–] [email protected] 0 points 3 months ago

Fake temps Per Second *FIFY

[–] [email protected] 0 points 3 months ago (1 children)

The pattern says liquid but the colors say heat damage. Both?

[–] [email protected] 0 points 3 months ago* (last edited 3 months ago) (1 children)

Hard to say. She's been in 24/7 service since 2017. Never had stability issues and I've tested it with Prime95 plenty of times upon upgrades. Last week I ran a Llama model and the computer froze hard. Even holding the power button wouldn't turn it off. Did the PSU power flip, came back up. Prime95 stable. Llama -> rip. Perhaps it's been cooked for a while and only trips by this workload. She's an old board, a Gigabyte with B350 running a 5950X (for a couple of years), so it's not super surprising that the power section has been a bit overused. 😅 Replacing with an X570 as we speak.

[–] [email protected] 0 points 3 months ago* (last edited 3 months ago) (4 children)

I think I found the source of the liquid @[email protected]. The thermal pad under the VRM heatsink has begun to liquefy into oily substance. This substance appears to have gone to the underside of the board through the vias around the VRM and discolored itself.

Some rubbing with isopropyl alcohol and it's almost gone:

Perhaps there's still life left in this board if used with an older chip.

[–] [email protected] 0 points 3 months ago

I think almost all thermal pads do this. Even my gpu with aftermarket thermal pads has these oil spots.

[–] [email protected] 0 points 3 months ago

Discovered exactly the same thing when I replaced my dead Gigabyte Z370 recently! Also took me a while to figure it out.

Both those chipsets were released in 2017 so I guess it's no surprise they were made with the same thermal pads.

[–] [email protected] 0 points 3 months ago (1 children)

I know it's completely irrelevant here, but what keyboard is that in the background? The keycaps look really nice.

[–] [email protected] 0 points 3 months ago (1 children)

Signature Plastics G20

They feel a bit like a mix between DSA and laptop keycaps.

[–] [email protected] 0 points 3 months ago (1 children)

Sounds pretty nice. Hope it's as enjoyable as it looks.

[–] [email protected] 0 points 3 months ago* (last edited 3 months ago)

It is. I just wish it wasn't this expensive. Will have to live with it for a while. 😅

[–] [email protected] 0 points 3 months ago (2 children)

Good detective work! Adding liquefying thermal pads as a reason to avoid Gigabyte.

[–] [email protected] 0 points 3 months ago

Why? I mean Gigabyte sucks balls but this stuff happens with thermal pads everywhere and it's not hurting anything.

[–] [email protected] 0 points 3 months ago (1 children)
[–] [email protected] 0 points 3 months ago

Asrock has done me well for budget builds, asus is what I happened to upgrade to for midrange. Honestly being dramatic, just haven't cared for GB historically.

[–] [email protected] 0 points 3 months ago

Looks like a direct motherboard RGB feature. It should boost your frames by 30%.

[–] [email protected] 0 points 3 months ago (1 children)

You need to find the magic smoke and push it back in, hurry!

[–] [email protected] 0 points 3 months ago

Funny enough, I can't detect the smell from hell. Could be COVID.

[–] [email protected] 0 points 3 months ago