That's not very typical, I'd like to make that clear.
this post was submitted on 29 Feb 2024
237 points (98.0% liked)
3DPrinting
15591 readers
10 users here now
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: [email protected] or [email protected]
There are CAD communities available at: [email protected] or [email protected]
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
founded 1 year ago
MODERATORS
You'll want to tow it outside the environment for repairs.
Into another environment?
No, past the environment
Well, what's out there?
Not sure if this was referencing it but just in case someone doesn't know:
Well sharing this at work and adding to new employee orientation along with the 7 parallel lines.
Don't forget about the turbo encabulator!
I did not know that one!
Honestly embarrassed to admit I've somehow never seen this one, but what a great clip lol
Here is an alternative Piped link(s):
https://www.piped.video/watch?v=3m5qxZm_JqM
Piped is a privacy-respecting open-source alternative frontend to YouTube.
I'm open-source; check me out at GitHub.
Remember when the kids braces tried to kill him in Poltergeist 2...?
Pepperidge YouTube remembers: https://www.youtube.com/watch?v=ayOLECuygTQ
Here is an alternative Piped link(s):
https://www.piped.video/watch?v=ayOLECuygTQ
Piped is a privacy-respecting open-source alternative frontend to YouTube.
I'm open-source; check me out at GitHub.
Alright… can someone explain to a non-Bambu guy….
Why they designed a cover that was so prone to falling off… as to warrant a sensor or whatever to detect it, instead of designing a cover that just doesn’t do that?
Normally the toolhead should never hit any object. If it does, and the cover detaches, it can be detected and the printer stopped before any significant damage is caused. Fallen off cover > broken machine.
The cover needs to be detachable to change or replace the hotend, and you need to have the cover for basic protection and better airflow control (I assume), and it's best practice to have a sensor to protect from user error. If the sensor is already there, why not also use it during the print?
I've printed on mine for nearly 1000hrs now, never had an issue with that or prints not sticking. Just have to prep it well and make sure there are no scraps under it.
It's held in with two fairly strong magnets, I don't think it falls off on its own. If a print falls over and catches on the extruder it could push the front off. I've had it happen for that reason.
Personally..... I'd just have left it off if I was them. I can't imagine a little plastic shield helps hot end temps
depending on the design, it might be to control air flow around the hot end's cooler block.
it's usually best to have some type of duct go from the fan and around the back of the block rather than just being open air- it keeps the air contained until it does it's job. But again, the only Bambu I saw was at microcenter and I was in a bit of a hurry so I didn't get a good look at it.
I was monitoring this print remotely (Bambu P1S), so I'm not sure what actually happened. It's possible that it failed for other reasons, and then the tool head got tangled in spaghetti and disassembled itself.
Hmm. that's plausible.
But it's still enough a problem that they programed an alert for it.
which means it's enough of a problem had a way to detect it.
feels like a case of not fixing the problem.
I think it's a good added measure to stop a print, in this case something caused the spaghetti, it would have kept causing spaghetti but the cover popping off stopped the print. I've got about 400 hrs on my p1s (upgraded from p1p), and I've never had the faceplate pop off. I would guess this is an isolated incident.
Coult be AI generating the message. Just kidding
All hail the robot overlords.