3DPrinting
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: [email protected] or [email protected]
There are CAD communities available at: [email protected] or [email protected]
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
view the rest of the comments
I have an Ender 3V2 that I converted to direct drive with linear rails and CR Touch, and was pretty happy with the reliability of it. I've been wanting to build a Voron forever, but the amount of hours to build/cost of a kit (I can't print ABS) was a barrier to entry.
I just picked up a Sovol SV08, which is a derivative of the Voron 2.4 (there are some proprietary parts on it, but $579 vs. $1000-1200 for a kit, I'm OK with that). I'm pretty happy with it thus far, although it did require some initial tinkering. Here are the highlights:
Time will tell if it's a long term printer, or more of a tinkerer. However, they open sourced it all - and there's already a ton of mods. Printing the housing for the BTT 5" touchscreen, saving me $50 over buying a touchscreen from Sovol. It might be worth a look.
2.4 owner here. Happy to hear some feedback on the SV08, it looks like a pretty good deal.
I'm surprised you saw that much of a speed improvement, but I guess I ran my old i3 clone somewhat fast. My print times were a bit faster on my Voron, thanks to cranking speed and acceleration, but the biggest time savings came from taking advantage of the much better hot end and using a 0.6mm nozzle with thicker line widths (I can cover nearly 2.0mm with two perimeters) and thicker layers (0.3 on most prints these days).
Were you homing z with the bed cold? If homing z involves touching the build plate, I could see this. You could probably just adjust your start g-code to accommodate this. One of the nice things about the 2.4 is that the z end stop is bolted to the frame, so as long as your print routine is consistent you can dial it pretty easily.
That said, just wait until you enclose your printer. The frame will grow in z fairly significantly as it heats up. I've not let my printer heat soak, printed a number of sequential parts in one print, and watched the first layer squish getting worse and worse with each sequential part. Eventually filament won't even stick to the build plate, so you need to tweak z-offset.
Jesus, is that what's going on... I enclosed my Franken-printer (well it was already enclosed but now it's less shitty) and my first layer kept growing, I figured it was an inconsistent BLTouch..
Aluminum's expansion coefficient is 0.000023m/C. Using my Voron, let's say the z extrusions are 530mm long and my extrusions go from 22 °C to 55 °C. This means they grow 0.35mm. That's in total, so the effect at the print head isn't 0.35mm, but let's say my gantry rides 25% of the way up. That's 0.0875mm, which is roughly 3x the z-offset of my last print.
My tuned/reliable profile (on Prusaslicer) on the Ender 3v2 was 40-60 mm/s and acceleration 200 mm/s^2. The stock profile (on Orca) for the SV08 is 200-300 mm/s and acceleration of 20000 mm/s^2. That's probably why such a dramatic speed increase.
The auto z-offset on the SV08 heats the bed to 65, then does a QGL, followed by cleaning the nozzle, then the z-offset calibration (using the inductive probe on both the bed and the z-offset probe), followed by a bed mesh, then a test print. Most of what I've read is that the heater is not the most efficient at heating the bed up completely. That's why everyone (Sovol included) recommend heat soaking for the initial z-offset. After I did that, I've had no problems with first layers.