I Made This

Furry serpents? Furry serpents.

cross-posted from: https://lemmy.world/post/16352007

Still needs some design corrections because I just didn't know how to properly do 3D print and industrial design but it works!

cross-posted from: https://sh.itjust.works/post/20133956

With the exception of the weight stack for my functional trainer and its change plates, I wanted all my subsequent equipment to be metric. To that end, I saw some cheap 45 lbs CAP bumper plates, and figured that I could make them into metric with not too much effort.

Some rough math prior to purchasing suggested that these plates -- with a width of 68 mm -- could be slimmed down from 20.4 kg (45 lbs) to nearly 20.0 kg, by boring two 2" holes (51 mm). To keep balance, the holes should be on on diametrically opposite ends. And should be neither too close to the edge, nor too close to the center, since the plate still needs to absorb a drop without deforming. That the bored holes are 51 mm is a fantastic happenstance, nearly identical to the center hole for Olympic-spec plates.

Examining each plate before drilling, I found that the silkscreen letter A in "CAP" is well-centered diametrically, although it doesn't line up with the matching logo on the back side. Also, since these are cheap CAP plates, the initial weight tolerances are pretty poor. 45 lbs should be 20.41 kg (2 sig figs), but my first four plates registered at 20.58, 20.51, 20.64, 20.56. That's nearly an extra half pound!

To drill the holes perfectly plumb, I did the work on a drill press using a 2-inch hole saw. Because the saw wasn't deep enough to go through the full width in one pass, I started with a 1/4-inch (6 mm) pilot hole straight through the tip of the letter A in "CAP". Then I drilled from both sides with the hole saw until a ~200 gram rubber core fell out. Repeat for the second bore.

To finish, I took some sandpaper to remove the old "45 lbs" markings, then used my label maker to affix new values. All plates are still high, but ranged from 20.030 kg to 20.105 kg. Not too shabby, I think.

In a happy coincidence, the position of these bored holes is perfect for one's thumbs when grasping the plate like a steering wheel, making it easier to pick up when laid flat on the floor. I also added a strip of blue electrical tape around the perimeter to make it easy to identify these as 20 kg.

In the end, I got the cheap metric plates I wanted, and it came with a usability improvement as well. I've not dropped these yet, so time will tell how they hold up.

If you use the right ink, the right plastic keycaps made for mechanical keyboards, and the right settings on your laser, you can effectively dye-sublimate any design you want.

https://pixelfed.social/i/web/post/699804325565108276

New Jam! This time its all about the retro gaming feel. Started out as me having fun making new chiptune-like presets on the MicroMonsta 2, ended up as a Jam. 😎🤖

Don't worry, this little angel respawns whenever he's eaten, and tastes like raspberry!

Had to upload this in .jpg form because Lemm.ee kept saying it's too large, I hope the quality isn't eaten too much!

Some WIPs:

https://imgur.com/a/5QQoVqC

The hardest part was by far getting the metal rings to look right!

Would love to hear all's thoughts!

cross-posted from: https://feddit.nl/post/14562342

Small 1:72 F4U Corsair model built in a weekend

Full album can be found at: https://www.scalemates.com/profiles/mate.php?id=118436&p=albums&album=111437&view=thumbs

Table saw to get straight sides. Belt sander to get a curve to the blade tip.

The spine doesn’t have a curve like a traditional bokken, but that doesn’t keep me from tucking this bad boy into my belt loop and walking around the house like a samurai :)

A little crochet flower I made before going to bed.

…to go with my hand-wired keyboard (or any keyboard). Numpad is “Masonite” hardboard I cut myself and painted with “textured” spray paint. I had the keyboard layout cut from aluminum by Xometry a few months back.

This is my first recorded Jam with the EP133. I have really mixed feelings about the EP133. On one hand its really fun to play around with, and make cool beats, but at the same time i find the Live performance experience to be, tricky at best. It requires way to many simultaneous button presses to perform things, and there are not enough options for scene transitions. (I want an option to change on pattern end, not just bar/tick)

As such this is not an optimal Jam, as i probably would have needed more time to rehearse, and in the end i also ended up cutting out a part in the middle of the video because awkward transitions and overall performance was not interesting to listen to.

I'm not quite ready to give up on the EP133, but I think i would need some really substantial software updates to be properly useful for me, and not just something fun to goof around with.... The frustrations in live play just makes me want to put it away and pull out the Circuit Tracks. :/

Pallet wood, wood stain and a torch

It was even the same brand. I love when hoarding materials pays off.

Made from sticks, wire and a plastic lid from a box of liquorice.

Fitting a braided bracelet like this is terrible btw

I’ve been making music for about 10 years but haven’t officially released anything. I’m hoping to release my first EP this year, though! This is one of the tracks that’s nearly finished.

Side note: does anyone here know of a community similar to r/wearethemusicmakers on Lemmy for music production?

Hand-wired, 3D printed case, laser cut switch plate, “laser dye sub” keycaps, custom layout.

Posted this on a couple of communities a while back, but I just subbed here and this board has actually worked really well.